Man Pages

rrdgraph_examples(1) - phpMan rrdgraph_examples(1) - phpMan

Command: man perldoc info search(apropos)  

RRDGRAPH_EXAMPLES(1)                rrdtool               RRDGRAPH_EXAMPLES(1)

       rrdgraph_examples - Examples for rrdtool graph

       rrdtool graph /home/httpd/html/test.png --img-format PNG

       followed by any of the examples below

       For your convenience some of the commands are explained here by using detailed examples. They are not always
       cut-and-paste ready because comments are intermixed with the examples.

   Data with multiple resolutions
           --end now --start end-120000s --width 400
           LINE1:ds0a#0000FF:"default resolution\l"
           LINE1:ds0b#00CCFF:"resolution 1800 seconds per interval\l"
           LINE1:ds0c#FF00FF:"resolution 7200 seconds per interval\l"

   Nicely formatted legend section

       Note: consolidation occurs here.


       Note: 10 spaces to move text to the right

           COMMENT:"          "

       Note: the column titles have to be as wide as the columns

           COMMENT:"Maximum    "
           COMMENT:"Average    "
           COMMENT:"Minimum    "

           COMMENT:"95th percentile\l"
           AREA:ds0bits#00C000:"Inbound "
           GPRINT:ds0max:"%6.2lf %Sbps"
           GPRINT:ds0avg:"%6.2lf %Sbps"
           GPRINT:ds0min:"%6.2lf %Sbps"
           GPRINT:ds0pct:"%6.2lf %Sbps\l"
           GPRINT:ds1max:"%6.2lf %Sbps"
           GPRINT:ds1avg:"%6.2lf %Sbps"
           GPRINT:ds1min:"%6.2lf %Sbps"
           GPRINT:ds1pct:"%6.2lf %Sbps\l"

   Offsetting a line on the y-axis
       Depending on your needs you can do this in two ways:

       ?   Offset the data, then graph this


           Note: this will also influence any other command that uses "data"

               LINE1:data#FF0000:"Data with offset"

       ?   Graph the original data, with an offset


           Note: no color in the first line so it is not visible


           Note: the second line gets stacked on top of the first one

               LINE1:data#FF0000:"Data with offset":STACK

   Drawing dashed lines
       Also works for HRULE and VRULE

       ?   default style: - - - - -
               LINE1:data#FF0000:"dashed line":dashes

       ?   more fancy style with offset: - -  --- -  --- -
               LINE1:data#FF0000:"another dashed line":dashes=15,5,5,10:dash-offset=10

   Time ranges
           Last four weeks: --start end-4w --end 00:00
           January 2001:    --start 20010101 --end start+31d
           January 2001:    --start 20010101 --end 20010201
           Last hour:       --start end-1h
           Last 24 hours:   <nothing at all>
           Yesterday:       --end 00:00

   Viewing the current and previous week together
           --end now --start end-1w

       Shift the data forward by one week (604800 seconds)

           [ more of the usual VDEF and CDEF stuff if you like ]
           AREA:lastweek#0000FF:Last\ week
           LINE1:thisweek#FF0000:This\ week

   Aberrant Behaviour Detection
       If the specialized function RRAs exist for aberrant behavior detection, they can be used to generate the graph
       of a time series with confidence bands and failures.

          rrdtool graph example.png \
                 DEF:obs=monitor.rrd:ifOutOctets:AVERAGE \
                 DEF:pred=monitor.rrd:ifOutOctets:HWPREDICT \
                 DEF:dev=monitor.rrd:ifOutOctets:DEVPREDICT \
                 DEF:fail=monitor.rrd:ifOutOctets:FAILURES \
                 TICK:fail#ffffa0:1.0:"Failures\: Average bits out" \
                 CDEF:scaledobs=obs,8,* \
                 CDEF:upper=pred,dev,2,*,+ \
                 CDEF:lower=pred,dev,2,*,- \
                 CDEF:scaledupper=upper,8,* \
                 CDEF:scaledlower=lower,8,* \
                 LINE2:scaledobs#0000ff:"Average bits out" \
                 LINE1:scaledupper#ff0000:"Upper Confidence Bound: Average bits out" \
                 LINE1:scaledlower#ff0000:"Lower Confidence Bound: Average bits out"

       This example generates a graph of the data series in blue (LINE2 with the scaledobs virtual data source),
       confidence bounds in red (scaledupper and scaledlower virtual data sources), and potential failures (i.e.
       potential aberrant aberrant behavior) marked by vertical yellow lines (the fail data source).

       The raw data comes from an AVERAGE RRA, the finest resolution of the observed time series (one consolidated
       data point per primary data point). The predicted (or smoothed) values are stored in the HWPREDICT RRA. The
       predicted deviations (think standard deviation) values are stored in the DEVPREDICT RRA. Finally, the FAILURES
       RRA contains indicators, with 1 denoting a potential failure.

       All of the data is rescaled to bits (instead of Octets) by multiplying by 8.  The confidence bounds are
       computed by an offset of 2 deviations both above and below the predicted values (the CDEFs upper and lower).
       Vertical lines indicated potential failures are graphed via the TICK graph element, which converts non-zero
       values in an RRA into tick marks. Here an axis-fraction argument of 1.0 means the tick marks span the entire
       y-axis, and hence become vertical lines on the graph.

       The choice of 2 deviations (a scaling factor) matches the default used internally by the FAILURES RRA. If the
       internal value is changed (see rrdtune), this graphing command should be changed to be consistent.

       A note on data reduction:

       The rrdtool graph command is designed to plot data at a specified temporal resolution, regardless of the
       actually resolution of the data in the RRD file.  This can present a problem for the specialized consolidation
       functions which maintain a one-to-one mapping between primary data points and consolidated data points. If a
       graph insists on viewing the contents of these RRAs on a coarser temporal scale, the graph command tries to do
       something intelligent, but the confidence bands and failures no longer have the same meaning and may be

       rrdgraph gives an overview of how rrdtool graph works.  rrdgraph_data describes DEF,CDEF and VDEF in detail.
       rrdgraph_rpn describes the RPN language used in the xDEF statements.  rrdgraph_graph page describes all the
       graph and print functions.

       Program by Tobias Oetiker <>

       This manual page by Alex van den Bogaerdt <> with corrections and/or additions by several

1.4.7                             2009-02-21              RRDGRAPH_EXAMPLES(1)