Man Pages

ipmi-oem(8) - phpMan ipmi-oem(8) - phpMan

Command: man perldoc info search(apropos)  


IPMI-OEM(8)                     System Commands                    IPMI-OEM(8)



NAME
       ipmi-oem - IPMI OEM utility

SYNOPSIS
       ipmi-oem [OPTION...] <OEMID> <OEMCOMMAND> [OEMOPTION...]

DESCRIPTION
       Ipmi-oem  is  used to execute OEM specific IPMI commands. It is intended to provide a better user interface for
       OEM specific IPMI commands rather than using ipmi-raw(8).

       Please see SUPPORTED OEM IDS and COMMANDS below for a list of supported OEM specific IPMI commands. A  list  of
       supported OEM specific commands may also be generated using the --list option.

       There are no guarantees that the below OEM commands will work on any particular motherboard. OEM extensions may
       or may not exist on particular hardware revisions and/or firmware revisions of motherboards. The extensions may
       or may not function for other lines of motherboards from the same manufacturer.

       Listed below are general IPMI options, tool specific options, trouble shooting information, workaround informa-
       tion, examples, and known issues. For a general introduction to FreeIPMI please see freeipmi(7).

GENERAL OPTIONS
       The following options are general options for configuring IPMI communication and executing  general  tool  com-
       mands.

       -D IPMIDRIVER, --driver-type=IPMIDRIVER
              Specify  the  driver  type to use instead of doing an auto selection.  The currently available outofband
              drivers are LAN and LAN_2_0, which perform IPMI 1.5 and IPMI 2.0 respectively. The  currently  available
              inband drivers are KCS, SSIF, OPENIPMI, and SUNBMC.

       --disable-auto-probe
              Do not probe in-band IPMI devices for default settings.

       --driver-address=DRIVER-ADDRESS
              Specify the in-band driver address to be used instead of the probed value. DRIVER-ADDRESS should be pre-
              fixed with "0x" for a hex value and '0' for an octal value.

       --driver-device=DEVICE
              Specify the in-band driver device path to be used instead of the probed path.

       --register-spacing=REGISTER-SPACING
              Specify the in-band driver register spacing instead of the probed value.  Argument  is  in  bytes  (i.e.
              32bit register spacing = 4)

       --target-channel-number=CHANNEL-NUMBER
              Specify the in-band driver target channel number to send IPMI requests to.

       --target-slave-address=SLAVE-ADDRESS
              Specify the in-band driver target slave number to send IPMI requests to.

       -h IPMIHOST1,IPMIHOST2,..., --hostname=IPMIHOST1[:PORT],IPMIHOST2[:PORT],...
              Specify  the  remote host(s) to communicate with. Multiple hostnames may be separated by comma or may be
              specified in a range format; see HOSTRANGED SUPPORT below. An optional port can be specified  with  each
              host, which may be useful in port forwarding or similar situations.

       -u USERNAME, --username=USERNAME
              Specify  the  username  to use when authenticating with the remote host.  If not specified, a null (i.e.
              anonymous) username is assumed. The required user privilege will depend on the oem commands executed.

       -p PASSWORD, --password=PASSWORD
              Specify the password to use when authenticationg with the remote host.  If not specified, a  null  pass-
              word is assumed. Maximum password length is 16 for IPMI 1.5 and 20 for IPMI 2.0.

       -P, --password-prompt
              Prompt for password to avoid possibility of listing it in process lists.

       -k K_G, --k-g=K_G
              Specify  the K_g BMC key to use when authenticating with the remote host for IPMI 2.0. If not specified,
              a null key is assumed. To input the key in hexadecimal form, prefix the string with '0x'. E.g., the  key
              'abc' can be entered with the either the string 'abc' or the string '0x616263'

       -K, --k-g-prompt
              Prompt for k-g to avoid possibility of listing it in process lists.

       --session-timeout=MILLISECONDS
              Specify  the  session timeout in milliseconds. Defaults to 20000 milliseconds (20 seconds) if not speci-
              fied.

       --retransmission-timeout=MILLISECONDS
              Specify the packet retransmission timeout in milliseconds. Defaults to 1000 milliseconds (1  second)  if
              not specified. The retransmission timeout cannot be larger than the session timeout.

       -a AUTHENTICATION-TYPE, --authentication-type=AUTHENTICATION-TYPE
              Specify  the IPMI 1.5 authentication type to use. The currently available authentication types are NONE,
              STRAIGHT_PASSWORD_KEY, MD2, and MD5. Defaults to MD5 if not specified.

       -I CIPHER-SUITE-ID, --cipher-suite-id=CIPHER-SUITE-ID
              Specify the IPMI 2.0 cipher suite ID to use. The Cipher Suite ID identifies  a  set  of  authentication,
              integrity,  and  confidentiality  algorithms to use for IPMI 2.0 communication. The authentication algo-
              rithm identifies the algorithm to use for session setup, the integrity algorithm  identifies  the  algo-
              rithm  to  use for session packet signatures, and the confidentiality algorithm identifies the algorithm
              to use for payload encryption. Defaults to cipher suite ID 3 if  not  specified.  The  following  cipher
              suite ids are currently supported:

              0 - Authentication Algorithm = None; Integrity Algorithm = None; Confidentiality Algorithm = None

              1 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm = None; Confidentiality Algorithm = None

              2  - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm = HMAC-SHA1-96; Confidentiality Algorithm
              = None

              3 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm = HMAC-SHA1-96; Confidentiality  Algorithm
              = AES-CBC-128

              6 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = None; Confidentiality Algorithm = None

              7 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = HMAC-MD5-128; Confidentiality Algorithm =
              None

              8 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = HMAC-MD5-128; Confidentiality Algorithm =
              AES-CBC-128

              11  -  Authentication  Algorithm  = HMAC-MD5; Integrity Algorithm = MD5-128; Confidentiality Algorithm =
              None

              12 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm =  MD5-128;  Confidentiality  Algorithm  =
              AES-CBC-128

              15  -  Authentication  Algorithm  = HMAC-SHA256; Integrity Algorithm = None; Confidentiality Algorithm =
              None

              16 - Authentication Algorithm = HMAC-SHA256;  Integrity  Algorithm  =  HMAC_SHA256_128;  Confidentiality
              Algorithm = None

              17  -  Authentication  Algorithm  =  HMAC-SHA256; Integrity Algorithm = HMAC_SHA256_128; Confidentiality
              Algorithm = AES-CBC-128

       -l PRIVILEGE-LEVEL, --privilege-level=PRIVILEGE-LEVEL
              Specify the privilege level to be used. The currently available privilege levels are USER, OPERATOR, and
              ADMIN. Defaults to ADMIN if not specified.

       --config-file=FILE
              Specify an alternate configuration file.

       -W WORKAROUNDS, --workaround-flags=WORKAROUNDS
              Specify workarounds to vendor compliance issues. Multiple workarounds can be specified separated by com-
              mas. A special command line flag of "none", will indicate no workarounds (may be useful  for  overriding
              configured defaults). See WORKAROUNDS below for a list of available workarounds.

       --debug
              Turn on debugging.

       -?, --help
              Output a help list and exit.

       --usage
              Output a usage message and exit.

       -V, --version
              Output the program version and exit.

SDR CACHE OPTIONS
       This tool requires access to the sensor data repository (SDR) cache for general operation. By default, SDR data
       will be downloaded and cached on the local machine. The following options apply to the SDR cache.

       -f, --flush-cache
              Flush a cached version of the sensor data repository (SDR) cache. The SDR is typically cached for faster
              subsequent  access. However, it may need to be flushed and re-generated if the SDR has been updated on a
              system.

       -Q, --quiet-cache
              Do not output information about cache creation/deletion. May be useful in scripting.

       --sdr-cache-recreate
              If the SDR cache is out of date or invalid, automatically recreate  the  sensor  data  repository  (SDR)
              cache. This option may be useful for scripting purposes.

       --sdr-cache-file=FILE
              Specify  a specific sensor data repository (SDR) cache file to be stored or read from. If this option is
              used when multiple hosts are specified, the same SDR cache file will be used for all hosts.

       --sdr-cache-directory=DIRECTORY
              Specify an alternate directory for sensor data repository (SDR)  caches  to  be  stored  or  read  from.
              Defaults to the home directory if not specified.

HOSTRANGED OPTIONS
       The  following options manipulate hostranged output. See HOSTRANGED SUPPORT below for additional information on
       hostranges.

       -B, --buffer-output
              Buffer hostranged output. For each node, buffer standard output until the node has  completed  its  IPMI
              operation.  When  specifying  this  option,  data  may appear to output slower to the user since the the
              entire IPMI operation must complete before any data can be output.  See  HOSTRANGED  SUPPORT  below  for
              additional information.

       -C, --consolidate-output
              Consolidate  hostranged  output. The complete standard output from every node specified will be consoli-
              dated so that nodes with identical output are not output twice. A header will list those nodes with  the
              consolidated  output.  When this option is specified, no output can be seen until the IPMI operations to
              all nodes has completed. If the user breaks out of the program early, all currently consolidated  output
              will be dumped. See HOSTRANGED SUPPORT below for additional information.

       -F NUM, --fanout=NUM
              Specify  multiple host fanout. A "sliding window" (or fanout) algorithm is used for parallel IPMI commu-
              nication so that slower nodes or timed out nodes will not impede  parallel  communication.  The  maximum
              number of threads available at the same time is limited by the fanout. The default is 64.

       -E, --eliminate
              Eliminate  hosts  determined  as  undetected by ipmidetect.  This attempts to remove the common issue of
              hostranged execution timing out due to several nodes being removed from service in a large cluster.  The
              ipmidetectd daemon must be running on the node executing the command.

       --always-prefix
              Always  prefix  output, even if only one host is specified or communicating in-band. This option is pri-
              marily useful for scripting purposes. Option will be ignored if specified with the -C option.

IPMI-OEM OPTIONS
       The following options are specific to Ipmi-oem.

       -L, --list
              List supported OEM IDs and Commands.

       -v, --verbose
              Output verbose information. Additional output will depend on specific OEM ID and OEM COMMANDS specified.

SUPPORTED OEM IDS and COMMANDS
       The  currently  supported  OEM IDs and COMMANDs are listed below. The special OEM ID of list may be passed into
       the list all supported OEM IDs and Commands. The special OEM command list may be passed to any OEM ID  to  list
       commands supported by that OEM ID.

       Dell

              get-system-info KEY
                     This  OEM  command  can  retrieve  the  motherboard  system  information.   Valid  keys are guid,
                     asset-tag, service-tag, chassis-service-tag, chassis-related-service-tag,  board-revision,  plat-
                     form-model-name,   slot-number,   system-revision,   idrac-info,  idrac-ipv4-url,  idrac-gui-web-
                     server-control, cmc-ipv4-url, cmc-ipv6-info, cmc-ipv6-url, mac-addresses.  Command  confirmed  to
                     work  on Dell Poweredge 2900, 2950, R610, R710, M600, M610, M610X, M910, and R905. However, indi-
                     vidual system information options may not be readable or available on every system.

              get-nic-selection
                     This OEM command will determine the current NIC selection for IPMI as dedicated,  shared,  shared
                     w/  failover to NIC2, or shared w/ failover to all. Dedicated indicates IPMI is only available on
                     an expansion card, shared indicates IPMI is available on NIC1, shared w/ failover to  NIC2  indi-
                     cates  IPMI is available on NIC1 w/ failover to NIC2 on NIC1's failure, and shared w/ failover to
                     all indicates IPMI is available on NIC1 w/ failover to all other NICs in the event of  NIC  fail-
                     ure. Command confirmed to work on Dell Poweredge 2900, 2950, R610, R710, and R905.

              set-nic-section dedicated|shared|shared_failover_nic2|shared_failover_all
                     This  OEM  command will set the current NIC selection to dedicated, shared, shared_failover_nic2,
                     or shared_failover_all. (See get-nic-selection above for description on inputs.)  On  older  Pow-
                     eredge systems, shared_failover_nic2 may have been documented as just failover. Command confirmed
                     to work on Dell Poweredge 2900, 2950, R610, R710, and R905.

              get-active-lom-status
                     This OEM command will get the current NIC being used for out of  band  management.  Command  con-
                     firmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).

              get-ssh-config
                     This  OEM  command  will get the current SSH configuration on the IPMI card. Command confirmed to
                     work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).

              set-ssh-config KEY=VALUE ...
                     This OEM command will set the current SSH configuration on the IPMI card. The possible  keys  and
                     values  are ssh=enable|disable, idletimeout=seconds, and portnumber=num. Multiple key=value pairs
                     may be specified. If no key=value pairs are specifed, available pairs are output. Some fields may
                     be  read-only on specific Poweredge systems. Command confirmed to work on Dell Poweredge R610 and
                     R710 (Dell 11G Poweredge systems).

              get-telnet-config
                     This OEM command will get the current telnet configuration on the IPMI card. Command confirmed to
                     work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).

              set-telnet-config KEY=VALUE ...
                     This  OEM  command  will set the current Telnet configuration on the IPMI card. The possible keys
                     and   values   are    telnet=enable|disable,    sessiontimeout=seconds,    portnumber=num,    and
                     7fls=enable|disable.  Multiple  key=value  pairs  may  be  specified.   If no key=value pairs are
                     specifed, available pairs are output. Some fields may be read-only on specific Poweredge systems.
                     Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).

              get-web-server-config
                     This  OEM  command  will  get the current web server configuration on the IPMI card. Command con-
                     firmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).

              set-web-server-config KEY=VALUE ...
                     This OEM command will set the current Web Server configuration on the  IPMI  card.  The  possible
                     keys  and  values  are  webserver=enable|disable, sessiontimeout=seconds, httpportnumber=num, and
                     httpsportnumber=num. Multiple key=value pairs  may  be  specified.  If  no  key=value  pairs  are
                     specifed, available pairs are output. Some fields may be read-only on specific Poweredge systems.
                     Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).

              get-active-directory-config
                     This OEM command will get the current active directory configuration on the  IPMI  card.  Command
                     confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).

              set-active-directory-config
                     This  OEM  command  will  set the current Web Server configuration on the IPMI card. The possible
                     keys and  values  are  activedirectory=enable|disable,  timeout=seconds,  type=extended|standard,
                     sso=enable|disable, and certificatevalidation=enable|disable. If no key=value pairs are specifed,
                     available pairs are output. Some fields may be read-only on specific Poweredge  systems.  Command
                     confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).

              reset-to-defaults
                     This  OEM  command will reset the BMC configuration back to default values. The command will spin
                     until the reset is confirmed to be complete. Command confirmed to work on Dell Poweredge R610 and
                     R710 (Dell 11G Poweredge systems).

              get-power-consumption-data
                     This OEM command can retrieve power consumption data. Command confirmed to work on Dell Poweredge
                     R610, R710, R905, M610, M610x, and M910.

              reset-power-consumption-data cumulative|peak
                     This  OEM  command  can  reset  the  cumulative  or  peak  power  consumption  data  (viewed  via
                     get-power-consumption-data).  Command confirmed to work on Dell Poweredge R610, R710, R905, M610,
                     M610x, and M910.

              power-supply-info
                     This OEM command can read and output power supply ratings and other information. This OEM command
                     requires access to the SDR. Command confirmed to work on Dell Poweredge R610, R710, and M610.

              get-instantaneous-power-consumption-data power_supply_instance
                     This OEM command can read instantaneous power consumption data. If a power supply instance number
                     is specified, only data for that instance will be gathered. Otherwise, collective power  consump-
                     tion  will  be gathered. Command confirmed to work on Dell Poweredge R610, R710, M610, M610x, and
                     M910.

              get-power-head-room
                     This OEM command can read power head room. Command confirmed to work on Dell Poweredge  R610  and
                     R710 (Dell 11G Poweredge systems).

              get-power-consumption-statistics average|max|min
                     This  OEM  command  can read average, max, or min power consumption history. Command confirmed to
                     work on Dell Poweredge R610, R710, M610, M610x, and M910.

              get-power-capacity
                     This OEM command can read the current power capacity. Command confirmed to work on Dell Poweredge
                     R610, R710, M610, M610x, and M910.

              set-power-capacity power-capacity
                     This  OEM command can write the current power capacity (specified in Watts). Command confirmed to
                     work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).

              get-power-capacity-status
                     This OEM command can determine if the current power capacity is enabled or disabled. Command con-
                     firmed to work on Dell Poweredge R610, R710, M610, M610x, and M910.

              set-power-capacity-status enable|disable
                     This OEM command can configure the current power capacity to be enabled or disabled. Command con-
                     firmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).

              get-chassis-identify-status
                     This OEM command will retrieve the current chassis identify (i.e. LED) status. Command  confirmed
                     to work on Dell Poweredge 2900, 2950, R610, R710, R905, M600, M610, M610x, and M910.

              slot-power-toggle slot-number
                     This  OEM command will perform a power toggle on a PCIe slot. The PCIe slot number can range from
                     1 to 16. Command confirmed to work on Dell Poweredge C410x.

              slot-power-control platform-model on|off|status slot-number
                     This OEM command will perform a power control action on a PCIe slot.  This OEM extension is  tied
                     very  closely  to  a platform, so a supported platform must be specified. The currently supported
                     platform-model options are C410x. The on action powers on a slot, off powers off a slot, and sta-
                     tus  returns  if  the current power is on or off. If the current power status is on, an on action
                     does nothing. Similarly, if the current power status is off, an off action does nothing. The  on,
                     off,  and  status  slot  power actions are not native and are emulated through a combination of a
                     power toggle (using slot-power-toggle above) and the reading of PCIe slot watt sensors. The  PCIe
                     slot number can range from 1 to 16. Command confirmed to work on Dell Poweredge C410x.

              get-port-map
                     This  OEM command will retrieve the current iPASS mapping to PCIe controllers/slots. Command con-
                     firmed to work on Dell Poweredge C410x.

              set-port-map jumper|bmc ipass-mapping 1:2|1:4|1:8
                     This OEM command will set an iPass mapping to PCIe controllers/slots.   jumper  or  bmc  must  be
                     specified  to  indicate  if  iPass mappings will be controlled via jumpers on the system or via a
                     BMC/IPMI. In order for reconfiguration to be done via ipmi-oem, the user  must  select  bmc.  The
                     ipass-mapping  determines which iPass ports will be mapped.  1:2, 1:4, and 1:8 determine the map-
                     ping that should be set. See details below for specific platforms. Command confirmed to  work  on
                     Dell  Poweredge  C410x.   For  the  Dell Poweredge C410x, the ipass-mapping ranges from 1 to 4. 1
                     refers to iPass 1 and 5, 2 to 2 and 6, 3 to 3 and 7, and 4 to 4 and 8. For  the  platform  C410x,
                     PCIe  slots 1, 2, 3, 4, 13, 14, 15, and 16 are attached to iPass 1, 2, 3, and 4. PCIe slots 5, 6,
                     7, 8, 9, 10, 11, and 12 are attached to iPass 5, 6, 7, and 8. For example, if 1:2 is set on  map-
                     ping-number  1,  PCIe  slots  1  and  15  will  be assigned to iPass 1 and slots 2 and 16 will be
                     assigned to iPass 5. if 1:4 is chosen, PCIe slots 1, 2, 15, and 16 will be assigned  to  iPass  1
                     and iPass 5 will not be used.

       Fujitsu

              get-power-on-source
                     This  OEM command will return the reason for the most recent Power On.  Command confirmed to work
                     on Fujitsu RX100 S5.

              get-power-off-source
                     This OEM command will return the reason for the most recent Power Off.  Command confirmed to work
                     on Fujitsu RX100 S5.

              get-remote-storage-status connection_number
                     This  OEM  command  will return the connection and/or status of remote storage. connection_number
                     currently supports a range of 0-1.  Command confirmed to work on Fujitsu RX100 S5.

              get-system-status
                     This OEM command will return the current system status. Command  confirmed  to  work  on  Fujitsu
                     RX100 S5.

              get-eeprom-version-info eeprom_number
                     This  OEM  command  will return the current version info for various hardware elements, including
                     firmware, SDR, and boot revision.  eeprom_number currently supports a range of 0-1. Command  con-
                     firmed to work on Fujitsu RX100 S5.

              get-identify-led
                     This  OEM  command will get the current identify LED status. Command confirmed to work on Fujitsu
                     RX100 S5.

              set-identify-led on|off
                     This OEM command will set the current identify LED status. Command confirmed to work  on  Fujitsu
                     RX100 S5.

              get-error-led
                     This  OEM  command  will  get  the current error LED status. Command confirmed to work on Fujitsu
                     RX100 S5.

              get-sel-entry-long-text sel_record_id
                     This OEM command will retrieve the Fujitsu specific string interpretation of a SEL  record.  This
                     command  may  be  useful  for interpreting Fujitsu OEM hex codes found in the SEL. A specific SEL
                     record ID must be specified. Please see ipmi-sel(8), for retrieving  SEL  records.  Command  con-
                     firmed to work on Fujitsu RX100 S5.

       IBM

              get-led
                     This  OEM  command  will get the current LED status. This OEM command requires access to the SDR.
                     Command confirmed to work on IBM x3755.

       Intel

              get-smtp-config [channel-number]
                     This OEM command will get the current SMTP configuration on the IPMI card. By default, configura-
                     tion  for every LAN channel will be output.  If a channel-number is specified, only that specific
                     channel number's configuration will be output.  Command confirmed to work on Intel S5500WB  (Pen-
                     guin Computing Relion 700) and Intel S2600JF (Appro 512X).

              set-smtp-config [channel-number] KEY=VALUE ...
                     This OEM command will set the current SMTP configuration on the IPMI card. By default, configura-
                     tion will be done for all LAN channels.  If a channel-number is  specified,  only  that  specific
                     channel   number's   configuration  will  be  configured.   The  possible  keys  and  values  are
                     smtp=enable|disable,   smtpserveraddress=ipaddress,   smtpusername=string,   userpassword=string,
                     emailaddress=string,  subject=string,  messagecontent=string, senderemailaddress=string, and smt-
                     phostname=string.  Multiple key=value pairs may be specified. If no key=value pairs are specifed,
                     available  pairs are output. Command confirmed to work on Intel S5500WB (Penguin Computing Relion
                     700) and Intel S2600JF (Appro 512X).

              get-power-restore-delay
                     This OEM command will retrieve the power on delay. The power on delay  is  a  delay  that  occurs
                     whenever  the  BMC turns on the system according to the Power Restore Policy setting. It does not
                     take effect otherwise (i.e. power button or Chassis Control). Command confirmed to work on  Intel
                     S2600JF (Appro 512X).

              set-power-restore-delay seconds
                     This  OEM command will set the power on delay. (See get-power-restore-delay above for description
                     on power restore delay). Command confirmed to work on Intel S2600JF (Appro 512X).

              restore-configuration
                     This OEM command will restore BMC configuration values back to default values. The  command  will
                     spin  until  the restore is confirmed to be complete. Command configured to work on Intel S5500WB
                     (Penguin Computing Relion 700) and Intel S2600JF (Appro 512X). After running  this  command,  the
                     BMC  must  be  reset  to return it to functioning status. This may be accomplished by executing a
                     cold-reset with bmc-device(8).

       IntelNM (Intel Node Manager)

       The following OEM commands operate on Intel chipsets with Node Manager support. They all require access to  the
       SDR. They may work on multiple vendors motherboards.


              get-node-manager-statistics [domainid=num] [policyid=num]
                     This OEM command will output the Intel Node Manager statistics. The user may optionally specify a
                     domainid or policyid. The default domainid is 0. If a policyid is specified, per  policy  statis-
                     tics  will  be  output,  otherwise global statistics will be output. Command confirmed to work on
                     Intel S5500WB (Penguin Computing Relion 700), Inventec 5441/5442  (Dell  Xanadu  II/III),  Quanta
                     S99Q  (Dell FS12-TY), Quanta QSSC-S4R (Appro GB812X-CN), Supermicro X9DRi-F, Intel S2600JF (Appro
                     512X).

              reset-node-manager-statistics [domainid=num] [policyid=num]
                     This OEM command will reset the Intel Node Manager statistics. The user may optionally specify  a
                     domainid  or  policyid. The default domainid is 0. If a policyid is specified, per policy statis-
                     tics will be reset, otherwise global statistics will be reset. Command confirmed to work on Intel
                     S5500WB  (Penguin  Computing  Relion  700),  Inventec 5441/5442 (Dell Xanadu II/III), Quanta S99Q
                     (Dell FS12-TY), Quanta QSSC-S4R (Appro  GB812X-CN),  Supermicro  X9DRi-F,  Intel  S2600JF  (Appro
                     512X).

              get-node-manager-capabilities [domainid=num] [policytrigger=none|inlet] [policytype=powercontrol]
                     This  OEM  command  will  output the current capabilities of the Intel Node manager. The user may
                     optionally specify a domainid, policytrigger, or policytype. The default domainid is  0.  If  any
                     particular  option is not specified, all permutations of the remaining options will be used in an
                     attempt to output all capabilities of the system. Command confirmed  to  work  on  Intel  S2600JF
                     (Appro 512X).

              node-manager-policy-control <enable|disable> [domainid=num] [policyid=num]
                     This OEM command will enable or disable the current global, domain, or policies used by the Intel
                     Node Manager. If no domainid is specified, then the Node Manager will be enabled or globally dis-
                     abled.   If  a  domainid  is  specified,  only that domain will be enabled or disabled. If both a
                     domainid and policyid are specified, only that specific policy within the domain will  be  speci-
                     fied. This OEM command will be required to enable or disable policies before many of the commands
                     below can be used for configuration or use. Command confirmed to work  on  Intel  S2600JF  (Appro
                     512X).

              get-node-manager-policy [domainid=num] [policyid=num]
                     This OEM command will get the current node manager policy. If no domainid is specified, all poli-
                     cies for all domain IDs and policy Ids will be attempted to be output. If a domainid is specified
                     but  a  policyid is not, all policies within a domain will be attempted to be output. If the ver-
                     bose option is set, additional error messages will be output as valid policies are being searched
                     for. Command confirmed to work on Intel S2600JF (Appro 512X).

              set-node-manager-policy  domainid=num policyid=num policytrigger=none|inlet powerlimit=watts correction-
              timelimit=ms policytriggerlimit=num statisticsreportingperiod=seconds [policystate=enable|disable] [pol-
              icyexceptionaction=alert|shutdown]
                     This OEM command will add or modify an indicated policy ID from the domain ID. Most of the fields
                     above are required, although they can be listed in any order.  By  default  any  created/modified
                     policy will be enabled, however this can be overridden by policystate.  policyexceptionaction may
                     be specified multiple times to configure multiple actions or  can  be  skipped  to  configure  no
                     actions.   When  the policytrigger is configured as none, the trigger that will lead to exception
                     actions is the value specified by the powerlimit. When the policytrigger  is  inlet,  the  tigger
                     that  will  lead  to exception actions is the value specified by policytriggerlimit. The units of
                     the policytriggerlimit will depend on the policytrigger selected.  Most  notably,  if  the  poli-
                     cytrigger is inlet, which refers to inlet temperature, the units of policytriggerlimit will be in
                     Celsius. When the policytrigger is none, the policytriggerlimit  is  ignored  internally  by  the
                     Intel  Node Manager, but a value must still be specified for configuration. Typically configuring
                     it to 0 is more than sufficient. The correctiontimelimit specifies the time the Node Manager must
                     take  corrective  actions to bring back the system within limits before taking the actions speci-
                     fied in policyexceptionaction. statisticsreportingperiod is the number of seconds  that  measured
                     power  will  be  averaged  for reporting.  Please see get-node-manager-policy to determine proper
                     ranges for powerlimit, correctiontimelimit,  policytriggerlimit,  and  statisticsreportingperiod.
                     Command confirmed to work on Intel S2600JF (Appro 512X).

              remove-node-manager-policy domainid=num policyid=num
                     This  OEM  command  will remove the indicated policy ID from the domain ID. Both the domainid and
                     policyid are required. Command confirmed to work on Intel S2600JF (Appro 512X).

              get-node-manager-alert-thresholds [domainid=num] [policyid=num]
                     This OEM command will get the current alert thresholds. If no domainid is  specified,  all  alert
                     thresholds  for domain IDs and policy Ids will be attempted to be output. If a domainid is speci-
                     fied but a policyid is not, all alert thresholds within a domain will be attempted to be  output.
                     The  units  of the thresholds will depend on the configuration of the current policy. If the ver-
                     bose option is set, additional error messages will be output as valid policies are being searched
                     for. Command confirmed to work on Intel S2600JF (Appro 512X).

              set-node-manager-alert-thresholds  domainid=num  policyid=num [threshold1=num] [threshold2=num] [thresh-
              old3=num]
                     This  OEM  command will set the alert thresholds for a given domain ID and policy ID. Up to three
                     thresholds can be specified, The units of the thresholds will depend on the configuration of  the
                     current policy. Command confirmed to work on Intel S2600JF (Appro 512X).

              get-node-manager-policy-suspend-periods [domainid=num] [policyid=num]
                     This  OEM  command  will get the current policy suspend periods. Suspend periods will temporarily
                     disable Intel Node Manager policies at configured times. If no domainid is specified, all suspend
                     periods for domain IDs and policy Ids will be attempted to be output.  If a domainid is specified
                     but a policyid is not, all suspend periods within a domain will be attempted to be output. If the
                     verbose  option  is  set,  additional  error  messages will be output as valid policies are being
                     searched for. Suspend start and stop times are output in 24 hour  format.  Command  confirmed  to
                     work on Intel S2600JF (Appro 512X).

              set-node-manager-policy-suspend-periods  domainid=num policyid=num suspendperiodstart1=time suspendperi-
              odstop1=time suspendperiodrepeat1=monday|tuesday|wednesday|thursday|friday|saturday|sunday ...
                     This  OEM  command  will  set the policy suspend periods for a policy.  Suspend periods will tem-
                     porarily disable Intel Node Manager policies at configured times. Up to 5 suspend periods can  be
                     specified  by  suspendperiodstartX,  suspendperiodstopX, suspendperiodrepeatX. suspendperiodstart
                     and suspendperiodstop specify the start and stop time since midnight for a  suspend  period.  The
                     time  should  be specified in 24 hour format (i.e. 02:00 or 13:40). Note that suspend periods are
                     configured in multiples of 6 minutes, therefore the stored configuration  may  be  rounded  to  a
                     slightly  alternate  configuration.   suspendperiodrepeat indicates the days in which the suspend
                     period shall be enabled. The option can be specified multiple times to configure multiple  times.
                     Command confirmed to work on Intel S2600JF (Appro 512X).

              set-node-manager-power-draw-range domainid=num minpowerdrawrange=watts maxpowerdrawrange=watts
                     This  OEM command will set the power draw range for a given domain ID.  After this configuration,
                     any policies within the domain ID that are outside of this range will be disabled as needed.  The
                     current  power  draw  range can be read via the get-node-manager-capabilities above. Command con-
                     firmed to work on Intel S2600JF (Appro 512X).

              get-node-manager-version
                     This OEM command will output the current Intel Node Manager  version  information.  Command  con-
                     firmed  to  work on Intel S5500WB (Penguin Computing Relion 700), Inventec 5441/5442 (Dell Xanadu
                     II/III), Quanta S99Q (Dell FS12-TY), Quanta QSSC-S4R  (Appro  GB812X-CN),  Intel  S2600JF  (Appro
                     512X).

       Inventec

              get-nic-mode
                     This  OEM command will determine the current NIC mode as dedicated or shared. Dedicated indicates
                     IPMI is only available on the dedicated management port. Shared indicates IPMI is also  available
                     on  one  of  the  primary  ethernet  ports. Command confirmed to work on Inventec 5441/5442 (Dell
                     Xanadu II/III).

              set-nic-mode dedicated|shared
                     This OEM command will set the current NIC mode to dedicated or shared.  (See  get-nic-mode  above
                     for  description  on  dedicated  vs. shared mode.) This OEM command may internally reset the BMC,
                     making the BMC unusable for awhile. Command confirmed to work on Inventec 5441/5442 (Dell  Xanadu
                     II/III).

              get-mac-address
                     This  command  will retrieve the BMC MAC address. This is actually not an OEM command, but rather
                     the normal IPMI MAC address command (identical to what is used in the bmc-config(8)  tool).  This
                     command is placed here for convenience.

              set-mac-address dedicated|shared MACADDR
                     This  OEM  command will set the dedicated or shared BMC MAC address.  (See get-nic-mode above for
                     description on dedicated vs. shared mode.) The BMC MAC address cannot be set through  the  normal
                     IPMI  MAC  address command (what is used in the bmc-config(8) tool). The MACADDR should be speci-
                     fied in XX:XX:XX:XX:XX:XX form. A shared BMC MAC address may conflict with  normal  communication
                     ethernet communication on the primary ethernet port. Users may wish to configuration an alternate
                     MAC address instead. After configuration of the MAC address, the BMC must be reset. This  may  be
                     accomplished by executing a cold-reset with bmc-device(8).  Command confirmed to work on Inventec
                     5441/5442 (Dell Xanadu II/III).

              get-bmc-services
                     This OEM command will display the currently enabled BMC services.  Command confirmed to  work  on
                     Inventec 5441/5442 (Dell Xanadu II/III).

              set-bmc-services enable|disable all|kvm|http|ssh
                     This  OEM command will enable or disable other BMC services besides IPMI. all can be specified to
                     enable/disable all services, kvm specifies KVM and  Virtual  Storage,  http  specifies  HTTP  and
                     HTTPS,  and  ssh  specifies  both SSH and Telnet. Command confirmed to work on Inventec 5441/5442
                     (Dell Xanadu II/III).

              get-authentication-config
                     This OEM command will display  additional  OEM  authentication  settings.   (See  set-authentica-
                     tion-config  below  for  description on outputs.) Command confirmed to work on Inventec 5441/5442
                     (Dell Xanadu II/III).

              set-authentication-config KEY=VALUE ...
                     This OEM command will set additional OEM authentication settings on the IPMI card.  The  possible
                     keys  and values are maxauthenticationfailures=count, lockoutwindow=seconds, lockouttime=seconds,
                     and httpsportnumber=num.  maxauthenticationfailures  specifies  the  maximum  number  of  allowed
                     authentication  failures.  lockoutwindow  specifies the window of time the authentication failure
                     count can be reached in to disable a user. lockouttime specifies the time period a user  is  dis-
                     abled  if the authentication failure count is reached. Setting 0 to any of the settings will dis-
                     able the lockout feature. Each time any of these settings is modified, the authentication failure
                     count  of  each  enabled  user  is  reset  to 0. Multiple key=value pairs may be specified. If no
                     key=value pairs are specifed, available pairs are output. Command confirmed to work  on  Inventec
                     5441/5442 (Dell Xanadu II/III).

              get-account-status
                     This OEM command will output the current account status of users on the BMC. This command is par-
                     ticularly usefor for determinining which users in the system may have been locked out via authen-
                     tication failures configured via set-authentication-config. Command confirmed to work on Inventec
                     5441/5442 (Dell Xanadu II/III).

              get-dns-config
                     This OEM command will display  additional  OEM  DNS  settings.   (See  set-dns-config  below  for
                     description on outputs.) Command confirmed to work on Inventec 5441/5442 (Dell Xanadu II/III).

              set-dns-config KEY=VALUE ...
                     This  OEM  command  will  set additional OEM DNS settings on the IPMI card. The possible keys and
                     values  are   dnsdhcp=enable|disable,   dnsserver1=ipaddress,   dnsserver2=ipaddress,   dnsregis-
                     terbmc=enable|disable,  dnsbmchostname=string,  dnsdomainnamedhcp=enable|disable,  and dnsdomain-
                     name=string. dnsdhcp specifies if the DNS server IP addresses should be assigned  from  the  DHCP
                     server.   dnsserver1  and dnsserver2 specify the IP addess for server 1 and 2 respectively. These
                     fields are read only if dnsdhcp and DHCP are enabled. dnsregisterbmc specifies if  the  BMC  host
                     name  is registered via the DNS server. dnsbmchostname specifies the BMC host name. This field is
                     read only if dnsregisterbmc is enabled. dnsdomainnamedhcp specifies if the DNS domainname  should
                     be  assigned from the DHCP server. dnsdomainname specifies the DNS domain name string. This field
                     is read only if dnsdomainnamedhcp is enabled. Multiple key=value pairs may be  specified.  If  no
                     key=value  pairs  are specifed, available pairs are output. Command confirmed to work on Inventec
                     5441/5442 (Dell Xanadu II/III).

              get-web-server-config
                     This OEM command will get the current web server configuration on the  IPMI  card.  Command  con-
                     firmed to work on Inventec 5441/5442 (Dell Xanadu II/III).

              set-web-server-config KEY=VALUE ...
                     This  OEM  command  will  set the current web server configuration on the IPMI card. The possible
                     keys and values are webserver=enable|disable, webservertimeout=seconds,  httpportnumber=num,  and
                     httpsportnumber=num.  Multiple  key=value  pairs  may  be  specified.  If  no key=value pairs are
                     specifed, available pairs are output. Command confirmed  to  work  on  Inventec  5441/5442  (Dell
                     Xanadu II/III).

              get-power-management-config
                     This  OEM  command  will get the current power management configuration on the IPMI card. Command
                     confirmed to work on Inventec 5441/5442 (Dell Xanadu II/III).

              set-power-management-config KEY=VALUE ...
                     This OEM command will set the current power management configuration on the IPMI card. The possi-
                     ble  keys  and  values  are dpnmpowermanagement=enable|disable, powerstaggeringacrecovery=immedi-
                     ate|auto|user, powerondelay=seconds, and maxpowerondelay=seconds.  dpnmpowermanagement enables or
                     diables  DPNM,  Dynamic Power Node Management. For powerstaggeringacrecovery, immediate specifies
                     no delay, auto generates a delay time between the minimum and maximum configured, and  user  uses
                     the  user defined time defined by powerondelay. powerondelay must be within the minimum and maxi-
                     mum power on delay times. Multiple key=value pairs may be specified. If no  key=value  pairs  are
                     specifed,  available  pairs  are  output.  Command  confirmed to work on Inventec 5441/5442 (Dell
                     Xanadu II/III).

              get-sol-idle-timeout
                     This OEM command will get the SOL idle timeout. Command confirmed to work on  Inventec  5441/5442
                     (Dell Xanadu II/III).

              set-sol-idle-timeout idle-timeout
                     This OEM command will set the SOL idle timeout. The idle-timeout is one-based, max of 65535, in 1
                     minute increments (e.g. 1 = 1 minute), 0 or "none" will configure no timeout.  Command  confirmed
                     to work on Inventec 5441/5442 (Dell Xanadu II/III).

              get-telnet-ssh-redirect-status
                     This  OEM command will get the telnet/SSH redirect status.  Command confirmed to work on Inventec
                     5442 (Dell Xanadu III).

              set-telnet-ssh-redirect-status enable|disable
                     This OEM command will enable or disable telnet/SSH redirect status.  Command confirmed to work on
                     Inventec 5442 (Dell Xanadu III).

              get-board-id
                     This  OEM  command  can  get  the board ID. Command confirmed to work on Inventec 5441/5442 (Dell
                     Xanadu II/III).

              set-board-id ID
                     This OEM command can set the board ID. Command confirmed to  work  on  Inventec  5441/5442  (Dell
                     Xanadu II/III).

              get-fcb-version
                     This  OEM  command can get the fan control board (FCB) version number.  Command confirmed to work
                     on Inventec 5441/5442 (Dell Xanadu II/III).

              set-fcb-version majorversion minorversion
                     This OEM command can set the fan control  board  (FCB)  version  number.   The  majorversion  and
                     minorversion  must  be  specified  in  hex. Command confirmed to work on Inventec 5441/5442 (Dell
                     Xanadu II/III).

              get-sol-inactivity-timeout
                     This OEM command will retrieve the SOL inactivity timeout. Command confirmed to work on  Inventec
                     5441/5442 (Dell Xanadu II/III).

              set-sol-inactivity-timeout inactivity-timeout
                     This OEM command will set the SOL inactivity timeout. The inactivity-timeout is one-based, max of
                     65535, in 1 minute increments (e.g. 1 = 1 minute), 0 or "none" will configure no  timeout.   Com-
                     mand confirmed to work on Inventec 5441/5442 (Dell Xanadu II/III).

              restore-to-defaults all|user|lan|sol|serial|pef
                     This OEM command will restore certain BMC configuration sections back to default values. The com-
                     mand will spin until the reset is confirmed to be complete. Command confirmed to work on Inventec
                     5442  (Dell  Xanadu III). After running this command, the BMC must be reset to return it to func-
                     tioning status. This may be accomplished by executing a cold-reset with bmc-device(8).

              read-eeprom at24c256n
                     This OEM command will read the specified eeprom. Command confirmed to work on Inventec 5441 (Dell
                     Xanadu II) for at24c256.

              clear-eeprom at24c256n
                     This OEM command will clear the specified eeprom, overwriting all bytes with 0xFF. If the verbose
                     option is set, progress percent will be output as the clearing is being done.  Command  confirmed
                     to work on Inventec 5441 (Dell Xanadu II) for at24c256.

       Quanta

              get-nic-mode
                     This  OEM command will determine the current NIC mode as dedicated or shared. Dedicated indicates
                     IPMI is only available on the dedicated management port. Shared indicates IPMI is also  available
                     on one of the primary ethernet ports. Command confirmed to work on Quanta S99Q (Dell FS12-TY).

              set-nic-mode dedicated|shared
                     This  OEM  command will set the current NIC mode to dedicated or shared.  (See get-nic-mode above
                     for description on dedicated vs. shared mode.) This OEM command may  internally  reset  the  BMC,
                     making the BMC unusable for awhile. Command confirmed to work on Quanta S99Q (Dell FS12-TY).

              get-bmc-services
                     This  OEM  command will display the currently enabled BMC services.  Command confirmed to work on
                     Quanta S99Q (Dell FS12-TY).

              set-bmc-services enable|disable all|kvm|http|ssh
                     This OEM command will enable or disable other BMC services besides IPMI. all can be specified  to
                     enable/disable  all  services,  kvm  specifies  KVM  and Virtual Storage, http specifies HTTP and
                     HTTPS, and ssh specifies both SSH and Telnet. Command confirmed to  work  on  Quanta  S99Q  (Dell
                     FS12-TY).

              get-account-status
                     This OEM command will output the current account status of users on the BMC. This command is par-
                     ticularly usefor for determinining which users in the system may have been locked out via authen-
                     tication failures. Command confirmed to work on Quanta S99Q (Dell FS12-TY).

              get-dns-config
                     This  OEM  command  will  display  additional  OEM  DNS  settings.  (See set-dns-config below for
                     description on outputs.) Command confirmed to work on Quanta S99Q (Dell FS12-TY).

              set-dns-config KEY=VALUE ...
                     This OEM command will set additional OEM DNS settings on the IPMI card.  The  possible  keys  and
                     values   are   dnsdhcp=enable|disable,   dnsserver1=ipaddress,   dnsserver2=ipaddress,  dnsregis-
                     terbmc=enable|disable, dnsbmchostname=string,  dnsdomainnamedhcp=enable|disable,  and  dnsdomain-
                     name=string.  dnsdhcp  specifies  if the DNS server IP addresses should be assigned from the DHCP
                     server.  dnsserver1 and dnsserver2 specify the IP addess for server 1 and 2  respectively.  These
                     fields  are  read  only if dnsdhcp and DHCP are enabled. dnsregisterbmc specifies if the BMC host
                     name is registered via the DNS server. dnsbmchostname specifies the BMC host name. This field  is
                     read  only if dnsregisterbmc is enabled. dnsdomainnamedhcp specifies if the DNS domainname should
                     be assigned from the DHCP server. dnsdomainname specifies the DNS domain name string. This  field
                     is  read  only  if dnsdomainnamedhcp is enabled. Multiple key=value pairs may be specified. If no
                     key=value pairs are specifed, available pairs are output. Command confirmed  to  work  on  Quanta
                     S99Q (Dell FS12-TY).

              get-web-server-config
                     This  OEM  command  will  get the current web server configuration on the IPMI card. Command con-
                     firmed to work on Quanta S99Q (Dell FS12-TY).

              set-web-server-config KEY=VALUE ...
                     This OEM command will set the current web server configuration on the  IPMI  card.  The  possible
                     keys  and  values are webserver=enable|disable, webservertimeout=seconds, httpportnumber=num, and
                     httpsportnumber=num. Multiple key=value pairs  may  be  specified.  If  no  key=value  pairs  are
                     specifed, available pairs are output. Command confirmed to work on Quanta S99Q (Dell FS12-TY).

              get-power-management-config
                     This  OEM  command  will get the current power management configuration on the IPMI card. Command
                     confirmed to work on Quanta S99Q (Dell FS12-TY).

              set-power-management-config KEY=VALUE ...
                     This OEM command will set the current power management configuration on the IPMI card. The possi-
                     ble  keys  and  values  are dpnmpowermanagement=enable|disable, powerstaggeringacrecovery=immedi-
                     ate|auto|user, powerondelay=seconds, and maxpowerondelay=seconds.  dpnmpowermanagement enables or
                     diables  DPNM,  Dynamic Power Node Management. For powerstaggeringacrecovery, immediate specifies
                     no delay, auto generates a delay time between the minimum and maximum configured, and  user  uses
                     the  user defined time defined by powerondelay. powerondelay must be within the minimum and maxi-
                     mum power on delay times. Multiple key=value pairs may be specified. If no  key=value  pairs  are
                     specifed, available pairs are output. Command confirmed to work on Quanta S99Q (Dell FS12-TY).

              get-sol-idle-timeout
                     This  OEM  command  will get the SOL idle timeout. Command confirmed to work on Quanta S99Q (Dell
                     FS12-TY).

              set-sol-idle-timeout idle-timeout
                     This OEM command will set the SOL idle timeout. The idle-timeout is one-based, max of 65535, in 1
                     minute  increments  (e.g. 1 = 1 minute), 0 or "none" will configure no timeout. Command confirmed
                     to work on Quanta S99Q (Dell FS12-TY).

              get-telnet-ssh-redirect-status
                     This OEM command will get the telnet/SSH redirect status. Command confirmed  to  work  on  Quanta
                     S99Q (Dell FS12-TY).

              set-telnet-ssh-redirect-status enable|disable
                     This OEM command will enable or disable telnet/SSH redirect status.  Command confirmed to work on
                     Quanta S99Q (Dell FS12-TY).

              reset-to-defaults all|user|lan|sol|serial|pef
                     This OEM command will reset certain BMC configuration sections back to default values.  The  com-
                     mand  will  spin until the reset is confirmed to be complete. Command confirmed to work on Quanta
                     S99Q (Dell FS12-TY).  After running this command, the BMC must be reset to return it to function-
                     ing status. This may be accomplished by executing a cold-reset with bmc-device(8).

              get-processor-information [processor-index]
                     This  OEM command will determine system processor information. By default, information about each
                     processor will be output. If a processor-index is specified, only that specific processor will be
                     output. Command confirmed to work on Quanta S99Q (Dell FS12-TY).

              read-mac-address s99q dedicated|shared
                     This  command  will read the currently configured dedicated or shared MAC address for a specified
                     motherboard. It will read the MAC address directly from the BMC eeprom. Command confirmed to work
                     on Quanta S99Q (Dell FS12-TY) for s99q.

              write-mac-address s99q dedicated|shared MACADDR
                     This OEM command will set the dedicated or shared BMC MAC address for a specified motherboard. It
                     will be written directly to the BMC eeprom. (See get-nic-mode above for description on  dedicated
                     vs.  shared  mode.) The BMC MAC address cannot be set through the normal IPMI MAC address command
                     (what is used in the bmc-config(8) tool). The MACADDR should be  specified  in  XX:XX:XX:XX:XX:XX
                     form.  A  shared BMC MAC address may conflict with normal communication ethernet communication on
                     the primary ethernet port. Users may wish to configuration  an  alternate  MAC  address  instead.
                     After  configuration  of the MAC address, the BMC must be reset. This may be accomplished by exe-
                     cuting a cold-reset with bmc-device(8).  Command confirmed to work on Quanta S99Q (Dell  FS12-TY)
                     for s99q.

       Sun

              get-led
                     This  OEM command will output current LED mode. off indicates the LED is steady off, on indicates
                     the LED is steady on, standby indicates the LED blinks at a 100ms on, 2900ms off rate, slow indi-
                     cates  the LED is blinking at 1Hz, and fast indicates the LED is blinking at 4Hz.  If the verbose
                     option is set, sensor names will be output with their entity ID and  instance  when  appropriate.
                     (Similar  to the --entity-sensor-names option in ipmi-sensors.)  This OEM command requires access
                     to the SDR. Command confirmed to work on Sun Fire 4140 with ILOM.

              set-led record_id off|on|standby|slow|fast
                     This OEM command will configure LED modes. (See get-led above for description on LED modes.) This
                     OEM command requires access to the SDR. Command confirmed to work on Sun Fire 4140 with ILOM.

       Supermicro

              extra-firmware-info
                     This  OEM command will output additional firmware version information.  Command confirmed to work
                     on Supermicro H8QME.

              reset-intrusion
                     This OEM command will reset the motherboard intrusion flag after it has been triggered. For exam-
                     ple, in ipmi-sensors or ipmi-sel, you may notice a 'General Chassis Intrusion' if the motherboard
                     chassis is not open, but was opened in the past. Command confirmed to work on Supermicro H8QME.

              get-bmc-services-status
                     This OEM command will determine if non-IPMI services (e.g. ssh, http, https, vnc, etc.) are  cur-
                     rently enabled or disabled on the BMC.  Command confirmed to work on Supermicro X8DTG.

              set-bmc-services-status enable|disable
                     This  OEM  command  will  enable or disable all non-IPMI services on the BMC. This command can be
                     used to enable or disable non-IPMI services such as ssh, http, https, and vnc. Command  confirmed
                     to work on Supermicro X8DTG.

       Wistron

              get-system-info KEY
                     This OEM command can retrieve the motherboard system information.  Valid keys are asset-tag, ser-
                     vice-tag, product-name. Command confirmed to work on Wistron / Dell Poweredge C6220.

              get-nic-mode
                     This OEM command will determine the current NIC mode as dedicated or shared. Dedicated  indicates
                     IPMI  is only available on the dedicated management port. Shared indicates IPMI is also available
                     on one of the primary ethernet ports. Command confirmed to  work  on  Wistron  /  Dell  Poweredge
                     C6220.

              set-nic-mode dedicated|shared
                     This  OEM  command will set the current NIC mode to dedicated or shared.  (See get-nic-mode above
                     for description on dedicated vs. shared mode.) After running this command, the BMC may need to be
                     reset to finalize the configuration. This may be accomplished by executing a cold-reset with bmc-
                     device(8).  Command confirmed to work on Wistron / Dell Poweredge C6220.

              get-shared-nic-selection
                     This OEM command will determine the current NIC IPMI is shared with if the mode is  shared.  (See
                     get-nic-mode  above  for  description on dedicated vs. shared mode.) Command confirmed to work on
                     Wistron / Dell Poweredge C6220.

              set-shared-nic-selection nic1|nic2|nic3|nic4|clear
                     This OEM command will set the current NIC sharing selection. If the current NIC mode is dedicated
                     it is advisable to clear this setting with the clear option. Command confirmed to work on Wistron
                     / Dell Poweredge C6220.

              get-bmc-services
                     This OEM command will display the currently enabled BMC services.  Command confirmed to  work  on
                     Wistron / Dell Poweredge C6220.

              set-bmc-services enable|disable all|kvm|http|ssh|snmp|telnet
                     This  OEM command will enable or disable other BMC services besides IPMI. all can be specified to
                     enable/disable all services, kvm specifies KVM and  Virtual  Storage,  http  specifies  HTTP  and
                     HTTPS. Command confirmed to work on Wistron / Dell Poweredge C6220.

              get-account-status
                     This OEM command will output the current account status of users on the BMC. This command is par-
                     ticularly usefor for determinining which users in the system may have been locked out via authen-
                     tication failures. Command confirmed to work on Wistron / Dell Poweredge C6220.

              get-dns-config
                     This  OEM  command  will  display  additional  OEM  DNS  settings.  (See set-dns-config below for
                     description on outputs.) Command confirmed to work on Wistron / Dell Poweredge C6220.

              set-dns-config KEY=VALUE ...
                     This OEM command will set additional OEM DNS settings on the IPMI card.  The  possible  keys  and
                     values   are   dnsdhcp=enable|disable,   dnsserver1=ipaddress,   dnsserver2=ipaddress,  dnsregis-
                     terbmc=enable|disable,   dnsbmchostname=string,   dnsdomainnamedhcp=enable|disable,    dnsdomain-
                     name=string,  and  dnsregistrationdelay=seconds. dnsdhcp specifies if the DNS server IP addresses
                     should be assigned from the DHCP server.  dnsserver1 and dnsserver2 specify  the  IP  addess  for
                     server  1 and 2 respectively. These fields are read only if dnsdhcp and DHCP are enabled. dnsreg-
                     isterbmc specifies if the BMC host name is registered via the DNS server.  dnsbmchostname  speci-
                     fies  the  BMC host name. This field is read only if dnsregisterbmc is enabled. dnsdomainnamedhcp
                     specifies if the DNS domainname should be assigned from the DHCP server. dnsdomainname  specifies
                     the DNS domain name string. This field is read only if dnsdomainnamedhcp is enabled. dnsregistra-
                     tiondelay specifies the delay the BMC should take after the IPMI process is up and running.  Mul-
                     tiple  key=value  pairs may be specified. If no key=value pairs are specifed, available pairs are
                     output. Command confirmed to work on Wistron / Dell Poweredge C6220.

              get-web-server-config
                     This OEM command will get the current web server configuration on the  IPMI  card.  Command  con-
                     firmed to work on Wistron / Dell Poweredge C6220.

              set-web-server-config KEY=VALUE ...
                     This  OEM  command  will  set the current web server configuration on the IPMI card. The possible
                     keys and values are webserver=enable|disable, webservertimeout=seconds,  httpportnumber=num,  and
                     httpsportnumber=num.  Multiple  key=value  pairs  may  be  specified.  If  no key=value pairs are
                     specifed, available pairs are output. Command confirmed to  work  on  Wistron  /  Dell  Poweredge
                     C6220.

              get-power-management-config
                     This  OEM  command  will get the current power management configuration on the IPMI card. Command
                     confirmed to work on Wistron / Dell Poweredge C6220.

              set-power-management-config KEY=VALUE ...
                     This OEM command will set the current power management configuration on the IPMI card. The possi-
                     ble  keys and values are powerstaggeringacrecovery=immediate|auto|user, powerondelay=seconds, and
                     maxpowerondelay=seconds. For powerstaggeringacrecovery, immediate specifies no delay, auto gener-
                     ates a delay time between the minimum and maximum configured, and user uses the user defined time
                     defined by powerondelay. powerondelay must be within the  minimum  and  maximum  power  on  delay
                     times.  Multiple  key=value pairs may be specified. If no key=value pairs are specifed, available
                     pairs are output. Command confirmed to work on Wistron / Dell Poweredge C6220.

              get-ipv6-settings
                     This OEM command will get the current IPv6 settings on the IPMI card. Command confirmed  to  work
                     on Wistron / Dell Poweredge C6220.

              set-ipv6-settings KEY=VALUE ...
                     This OEM command will set the current IPv6 settings on the IPMI card.  The possible keys and val-
                     ues  are  ipv6=enable|disable,  ipv6address=ipaddress,   ipv6gatewayaddress=ipaddress,   ipv6pre-
                     fixlength=length, ipv6autoconfig=enable|disable, ipv6autodns=enable|disable, ipv6dnsserver1=ipad-
                     dress, and ipv6dnsserver2=ipaddress. If no key=value pairs  are  specifed,  available  pairs  are
                     output.  Some fields may be read-only on specific Poweredge systems. Command confirmed to work on
                     Wistron / Dell Poweredge C6220.

              get-ipv6-trap-settings
                     This OEM command will get the current IPv6 SNMP trap settings on the IPMI card. Command confirmed
                     to work on Wistron / Dell Poweredge C6220.

              set-ipv6-trap-settings index KEY=VALUE ...
                     This  OEM  command will set the current IPv6 SNMP trap settings on the IPMI card. The index indi-
                     cates the index position for the configuration. It is followed by a set of configuration keys and
                     values.  The possible keys and values are destinationtype=pet|oem1|oem2, alertacktimeout=seconds,
                     retries=count, and ipv6snmptrapaddress=ipaddress. If no key=value pairs are  specifed,  available
                     pairs  are  output. Some fields may be read-only on specific Poweredge systems. Command confirmed
                     to work on Wistron / Dell Poweredge C6220.

              get-sol-idle-timeout
                     This OEM command will get the SOL idle timeout. Command confirmed to work on Wistron / Dell  Pow-
                     eredge C6220.

              set-sol-idle-timeout idle-timeout
                     This OEM command will set the SOL idle timeout. The idle-timeout is one-based, max of 65535, in 1
                     minute increments (e.g. 1 = 1 minute), 0 or "none" will configure no timeout.  Command  confirmed
                     to work on Wistron / Dell Poweredge C6220.

              get-telnet-redirect-function
                     This  OEM  command  will get the telnet redirect function. Command confirmed to work on Wistron /
                     Dell Poweredge C6220.

              set-telnet-redirect-function disable|solenable|smashenable
                     This OEM command will enable or disable telnet redirect function.  Command confirmed to  work  on
                     Wistron / Dell Poweredge C6220.

              get-dhcp-retry
                     This OEM command will retrieve DHCP retry information. Wistron / Dell Poweredge C6220.

              set-dhcp-retry retry-count retry-interval retry-timeout
                     This  OEM command will set DHCP retry information. The retry-count is one-based, max of 254, 0 or
                     "none" will configure no retries, 255  or  "indefinite"  will  configure  constant  retries.  The
                     retry-interval  is one-based, in 10 second increments (e.g. 1 = 10 seconds). The retry-timeout is
                     one-based, in 1 minute increments (e.g. 1 = 1 minute).  After running this command, the  BMC  may
                     need  to  be  reset  to finalize the configuration. This may be accomplished by executing a cold-
                     reset with bmc-device(8).  Command confirmed to work on Wistron / Dell Poweredge C6220.

              get-link-status-change-control
                     This OEM command will get the current link status  change  control.  If  it  reports  "Link  Down
                     Resilience  Enabled",  BMC  firmware  will do nothing upon detecting Link Status Change until the
                     DHCP lease is expired. If it reports "DHCP Re-Discovery Enabled", BMC firmware will perform  DHCP
                     Discovery  upon  detecting  link  status  going  down  than back up. Command confirmed to work on
                     Wistron / Dell Poweredge C6220..

              set-link-status-change-control link_resilience|dhcp_rediscovery
                     This OEM command will set the current NIC link status change control setting. (See  set-link-sta-
                     tus-change-control  above  for description of arguments). After running this command, the BMC may
                     need to be reset to finalize the configuration. This may be accomplished  by  executing  a  cold-
                     reset with bmc-device(8).  Command confirmed to work on Wistron / Dell Poweredge C6220.

              set-password-policy <enable|disable>
                     This OEM command will set the current password policy enforcement. If password policy is enabled,
                     BMC passwords must meet the following requirements: Not contain the user's name, be 8-14  charac-
                     ters  long,  and  contain  three  of the following four, an English uppercase character (A-Z), an
                     English lowercase character (a-z), a digit (0-9), a special character (!, $, #, %, etc.). Command
                     confirmed to work on Wistron / Dell Poweredge C6220.

              read-proprietary-string
                     This OEM command will read the proprietary string stored in the FRU.  The proprietary string is a
                     string the user may set for any management purpose. It can also be read  via  ipmi-fru.   Command
                     confirmed to work on Wistron / Dell Poweredge C6220.

              set-proprietary-string <string>
                     This  OEM command will write the proprietary string stored in the FRU.  The maximum length string
                     is 80 characters. Command confirmed to work on Wistron / Dell Poweredge C6220.

              clear-proprietary-string
                     This OEM command will clear the proprietary string stored in the FRU.  Command confirmed to  work
                     on Wistron / Dell Poweredge C6220.

HOSTRANGED SUPPORT
       Multiple hosts can be input either as an explicit comma separated lists of hosts or a range of hostnames in the
       general form: prefix[n-m,l-k,...], where n < m and l < k, etc. The later form should not be confused with regu-
       lar  expression  character  classes (also denoted by []). For example, foo[19] does not represent foo1 or foo9,
       but rather represents a degenerate range: foo19.

       This range syntax is meant only as a convenience on clusters with a prefixNN naming convention  and  specifica-
       tion  of  ranges should not be considered necessary -- the list foo1,foo9 could be specified as such, or by the
       range foo[1,9].

       Some examples of range usage follow:
           foo[01-05] instead of foo01,foo02,foo03,foo04,foo05
           foo[7,9-10] instead of foo7,foo9,foo10
           foo[0-3] instead of foo0,foo1,foo2,foo3

       As a reminder to the reader, some shells will interpret brackets ([ and ]) for pattern matching.  Depending  on
       your shell, it may be necessary to enclose ranged lists within quotes.

       When  multiple  hosts  are specified by the user, a thread will be executed for each host in parallel up to the
       configured fanout (which can be adjusted via the -F option). This will allow communication to large numbers  of
       nodes far more quickly than if done in serial.

       By  default,  standard output from each node specified will be output with the hostname prepended to each line.
       Although this output is readable in many situations, it may be difficult to read in other situations. For exam-
       ple,  output  from  multiple  nodes  may  be  mixed  together. The -B and -C options can be used to change this
       default.

       In-band IPMI Communication will be used when the host "localhost" is specified. This allows the user to add the
       localhost into the hostranged output.

GENERAL TROUBLESHOOTING
       Most often, IPMI problems are due to configuration problems.

       IPMI  over  LAN problems involve a misconfiguration of the remote machine's BMC.  Double check to make sure the
       following are configured properly in the remote machine's BMC: IP address, MAC address, subnet mask,  username,
       user  enablement,  user privilege, password, LAN privilege, LAN enablement, and allowed authentication type(s).
       For IPMI 2.0 connections, double check to make sure the cipher suite privilege(s) and K_g  key  are  configured
       properly. The bmc-config(8) tool can be used to check and/or change these configuration settings.

       Inband IPMI problems are typically caused by improperly configured drivers or non-standard BMCs.

       In  addition  to  the  troubleshooting tips below, please see WORKAROUNDS below to also if there are any vendor
       specific bugs that have been discovered and worked around.

       Listed below are many of the common issues for error messages.   For  additional  support,  please  e-mail  the
       <freeipmi-usersATgnu.org> mailing list.

       "username  invalid"  -  The  username  entered (or a NULL username if none was entered) is not available on the
       remote machine. It may also be possible the remote BMC's username configuration is incorrect.

       "password invalid" - The password entered (or a NULL password if none was entered) is not correct. It may  also
       be possible the password for the user is not correctly configured on the remote BMC.

       "password  verification  timeout" - Password verification has timed out.  A "password invalid" error (described
       above) or a generic "session timeout" (described below) occurred.  During this point in the protocol it  cannot
       be differentiated which occurred.

       "k_g invalid" - The K_g key entered (or a NULL K_g key if none was entered) is not correct. It may also be pos-
       sible the K_g key is not correctly configured on the remote BMC.

       "privilege level insufficient" - An IPMI command requires a higher user privilege than  the  one  authenticated
       with.  Please  try to authenticate with a higher privilege. This may require authenticating to a different user
       which has a higher maximum privilege.

       "privilege level cannot be obtained for this user" - The privilege level you  are  attempting  to  authenticate
       with  is higher than the maximum allowed for this user. Please try again with a lower privilege. It may also be
       possible the maximum privilege level allowed for a user is not configured properly on the remote BMC.

       "authentication type unavailable for attempted privilege level" - The authentication type you wish to authenti-
       cate  with is not available for this privilege level. Please try again with an alternate authentication type or
       alternate privilege level. It may also be possible the available authentication types you can authenticate with
       are not correctly configured on the remote BMC.

       "cipher  suite  id  unavailable"  -  The  cipher suite id you wish to authenticate with is not available on the
       remote BMC. Please try again with an alternate cipher suite id. It may also be possible  the  available  cipher
       suite ids are not correctly configured on the remote BMC.

       "ipmi 2.0 unavailable" - IPMI 2.0 was not discovered on the remote machine. Please try to use IPMI 1.5 instead.

       "connection timeout" - Initial IPMI communication failed. A number of potential errors are possible,  including
       an invalid hostname specified, an IPMI IP address cannot be resolved, IPMI is not enabled on the remote server,
       the network connection is bad, etc. Please verify configuration and connectivity.

       "session timeout" - The IPMI session has timed out. Please reconnect.  If this error occurs often, you may wish
       to increase the retransmission timeout. Some remote BMCs are considerably slower than others.

       "device  not  found"  -  The  specified device could not be found. Please check configuration or inputs and try
       again.

       "driver timeout" - Communication with the driver or device has timed out. Please try again.

       "message timeout" - Communication with the driver or device has timed out. Please try again.

       "BMC busy" - The BMC is currently busy. It may be processing information or have too many simultaneous sessions
       to manage. Please wait and try again.

       "could  not  find  inband device" - An inband device could not be found.  Please check configuration or specify
       specific device or driver on the command line.

       "driver timeout" - The inband driver has timed out communicating to the local BMC or service processor. The BMC
       or service processor may be busy or (worst case) possibly non-functioning.

WORKAROUNDS
       With  so  many  different  vendors implementing their own IPMI solutions, different vendors may implement their
       IPMI protocols incorrectly. The following describes a number of workarounds currently available to handle  dis-
       covered  compliance issues. When possible, workarounds have been implemented so they will be transparent to the
       user. However, some will require the user to specify a workaround be used via the -W option.

       The hardware listed below may only indicate the hardware that a problem was discovered on.  Newer  versions  of
       hardware  may  fix  the problems indicated below. Similar machines from vendors may or may not exhibit the same
       problems. Different vendors may license their firmware from the same IPMI firmware  developer,  so  it  may  be
       worthwhile to try workarounds listed below even if your motherboard is not listed.

       If  you  believe  your  hardware  has an additional compliance issue that needs a workaround to be implemented,
       please contact the FreeIPMI maintainers on <freeipmi-usersATgnu.org> or <freeipmi-develATgnu.org>.

       assumeio - This workaround flag will assume inband interfaces communicate with system  I/O  rather  than  being
       memory-mapped.  This  will work around systems that report invalid base addresses. Those hitting this issue may
       see "device not supported" or "could not find inband device" errors.  Issue observed on HP ProLiant DL145 G1.

       spinpoll - This workaround flag will inform some inband drivers (most notably the KCS  driver)  to  spin  while
       polling rather than putting the process to sleep. This may significantly improve the wall clock running time of
       tools because an operating system scheduler's granularity may be much larger than the time it takes to  perform
       a  single IPMI message transaction. However, by spinning, your system may be performing less useful work by not
       contexting out the tool for a more useful task.

       authcap - This workaround flag will skip early checks for username capabilities,  authentication  capabilities,
       and  K_g  support and allow IPMI authentication to succeed. It works around multiple issues in which the remote
       system does not properly report username capabilities, authentication capabilities, or K_g status.  Those  hit-
       ting this issue may see "username invalid", "authentication type unavailable for attempted privilege level", or
       "k_g invalid" errors.  Issue observed on Asus P5M2/P5MT-R/RS162-E4/RX4,  Intel  SR1520ML/X38ML,  and  Sun  Fire
       2200/4150/4450 with ELOM.

       idzero  -  This workaround flag will allow empty session IDs to be accepted by the client. It works around IPMI
       sessions that report empty session IDs to the client. Those  hitting  this  issue  may  see  "session  timeout"
       errors. Issue observed on Tyan S2882 with M3289 BMC.

       unexpectedauth  -  This  workaround  flag will allow unexpected non-null authcodes to be checked as though they
       were expected. It works around an issue when packets contain non-null authentication data when they  should  be
       null  due  to  disabled  per-message authentication. Those hitting this issue may see "session timeout" errors.
       Issue observed on Dell PowerEdge 2850,SC1425. Confirmed fixed on newer firmware.

       forcepermsg - This workaround flag will force per-message authentication to be used no matter  what  is  adver-
       tised  by the remote system. It works around an issue when per-message authentication is advertised as disabled
       on the remote system, but it is actually required for the protocol. Those hitting this issue may  see  "session
       timeout" errors.  Issue observed on IBM eServer 325.

       endianseq  -  This workaround flag will flip the endian of the session sequence numbers to allow the session to
       continue properly. It works around IPMI 1.5 session sequence numbers that are the wrong endian.  Those  hitting
       this  issue  may see "session timeout" errors. Issue observed on some Sun ILOM 1.0/2.0 (depends on service pro-
       cessor endian).

       noauthcodecheck - This workaround flag will tell FreeIPMI to not check the authentication codes  returned  from
       IPMI  1.5  command  responses. It works around systems to return invalid authentication codes due to hashing or
       implementation errors. Users are cautioned on the use of this option, as it  removes  an  authentication  check
       verifying  the  validity  of a packet. However, in most organizations, this is unlikely to be a security issue.
       Those hitting this issue may see "connection timeout", "session timeout", or  "password  verification  timeout"
       errors.  Issue observed on Xyratex FB-H8-SRAY.

       intel20  -  This workaround flag will work around several Intel IPMI 2.0 authentication issues. The issues cov-
       ered include padding of usernames, and password truncation if the  authentication  algorithm  is  HMAC-MD5-128.
       Those  hitting  this  issue  may  see  "username  invalid",  "password invalid", or "k_g invalid" errors. Issue
       observed on Intel SE7520AF2 with Intel Server Management Module (Professional Edition).

       supermicro20 - This workaround flag will work around several Supermicro IPMI 2.0 authentication issues on moth-
       erboards  w/  Peppercon IPMI firmware. The issues covered include handling invalid length authentication codes.
       Those hitting this issue may see "password invalid" errors.  Issue observed  on  Supermicro  H8QME  with  SIMSO
       daughter card. Confirmed fixed on newerver firmware.

       sun20  - This workaround flag will work work around several Sun IPMI 2.0 authentication issues. The issues cov-
       ered include invalid lengthed hash keys, improperly hashed keys, and invalid cipher suite records.  Those  hit-
       ting  this  issue  may see "password invalid" or "bmc error" errors.  Issue observed on Sun Fire 4100/4200/4500
       with ILOM.  This workaround automatically includes the "opensesspriv" workaround.

       opensesspriv - This workaround flag will slightly alter FreeIPMI's IPMI 2.0 connection protocol  to  workaround
       an  invalid hashing algorithm used by the remote system. The privilege level sent during the Open Session stage
       of an IPMI 2.0 connection is used for hashing keys instead of the privilege level sent during the RAKP1 connec-
       tion  stage.  Those hitting this issue may see "password invalid", "k_g invalid", or "bad rmcpplus status code"
       errors.  Issue observed on Sun Fire 4100/4200/4500 with ILOM, Inventec 5441/Dell Xanadu II,  Supermicro  X8DTH,
       Supermicro  X8DTG,  Intel  S5500WBV/Penguin  Relion  700,  Intel S2600JF/Appro 512X, and Quanta QSSC-S4R//Appro
       GB812X-CN. This workaround is automatically triggered with the "sun20" workaround.

       integritycheckvalue - This workaround flag will work around an invalid integrity check value during an IPMI 2.0
       session  establishment  when using Cipher Suite ID 0. The integrity check value should be 0 length, however the
       remote motherboard responds with a non-empty field. Those hitting this issue  may  see  "k_g  invalid"  errors.
       Issue  observed  on  Supermicro  X8DTG,  Supermicro  X8DTU,  and  Intel  S5500WBV/Penguin Relion 700, and Intel
       S2600JF/Appro 512X.

       assumemaxsdrrecordcount - This workaround will inform SDR reading to stop reading after a known  maximum  numer
       of  SDR  records  have been read. This will work around systems that have mis-implemented SDR reading functions
       that. Those hitting this issue may see "SDR record count invalid" errors. Issue observed on unspecified  Inspur
       motherboard.

       No  IPMI  1.5  Support - Some motherboards that support IPMI 2.0 have been found to not support IPMI 1.5. Those
       hitting this issue may see "ipmi 2.0 unavailable" or "connection timeout" errors.  This  issue  can  be  worked
       around  by using IPMI 2.0 instead of IPMI 1.5 by specifying --driver-address=LAN_2_0. Issue observed on HP Pro-
       liant DL 145.

DIAGNOSTICS
       Upon successful execution, exit status is 0. On error, exit status is 1.

       If multiple hosts are specified for communication, the exit status is 0 if and only if all targets successfully
       execute. Otherwise the exit status is 1.

KNOWN ISSUES
       On  older  operating  systems,  if  you  input your username, password, and other potentially security relevant
       information on the command line, this information may be discovered by other users when using  tools  like  the
       ps(1)  command  or  looking in the /proc file system. It is generally more secure to input password information
       with options like the -P or -K options. Configuring security relevant information in the FreeIPMI configuration
       file would also be an appropriate way to hide this information.

       In  order to prevent brute force attacks, some BMCs will temporarily "lock up" after a number of remote authen-
       tication errors. You may need to wait awhile in order to this temporary  "lock  up"  to  pass  before  you  may
       authenticate again.

REPORTING BUGS
       Report bugs to <freeipmi-usersATgnu.org> or <freeipmi-develATgnu.org>.

COPYRIGHT
       Copyright (C) 2008-2012 FreeIPMI Core Team

       This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Pub-
       lic License as published by the Free Software Foundation; either version 3 of the License, or (at your  option)
       any later version.

SEE ALSO
       freeipmi(7), bmc-config(8), bmc-device(8), ipmi-pef-config(8), ipmi-raw(8)

       http://www.gnu.org/software/freeipmi/



IPMI OEM version 1.2.1            2017-03-22                       IPMI-OEM(8)